Aim Various forms of temporary resins are offered on the market; however, the properties of temporary resins obtained by milling and 3D printing have not been fully examined. This study aimed to compare the flexural strength and Vickers hardness of milled and 3D-printed resins. Methods Three resins were tested: Evolux PMMA (milled resin), Cosmos Temp (3D-printed resin), and Structur 2 SC (bis-acrylic resin, group control). Specimens were prepared with rectangular shapes (n = 12) for flexural strength measurements and disc shapes (n = 9) for Vickers hardness tests. Flexural strength tests were performed at a crosshead speed of 0.75 mm/min, and the Vickers hardness was measured under a load of 20 N for 10 s. The obtained data were subjected to the Kruskal–Wallis test. Results A significant difference (p < 0.05) in flexural strength was observed among the three sample groups: Evolux PMMA (111.76 MPa), Structur 2 SC (87.34 MPa), and Cosmos Temp (56.83 MPa). No significant difference (p < 0.05) was observed between the Vickers hardness values of Structur 2 SC (33.37 VHN) and Evolux PMMA (29.11 VHN); however, both materials were statistically superior to Cosmos Temp (10.90 VHN). Conclusion While the mechanical properties of the milled resin were superior or similar to those of the bis-acrylic resin, the 3D-printed resin was statistically inferior to both the milled and bis-acrylic resins.

Introdução As dimensões corretas de um retentor intrarradicular são bastante relevantes para a longevidade de uma prótese. Objetivo O objetivo deste estudo foi comprovar se as dimensões de retentores metálicos fundidos estão de acordo com critérios clínicos ideais. Material e método Foram analisadas 285 radiografias periapicais de diagnóstico, totalizando 80 dentes, de pacientes que procuraram atendimento na Faculdade de Odontologia/UFG, no período de março de 2008 a outubro de 2012. Foram incluídas no estudo as radiografias periapicais de dentes unirradiculares, que apresentavam retentor intrarradicular metálico fundido. A avaliação radiográfica foi realizada em ambiente com pouca luminosidade e com auxílio de um negatoscópio com lupa. A dimensão dos retentores foi estabelecida através de um paquímetro digital considerando as seguintes medidas: a) comprimento do remanescente (CR); b) comprimento do retentor intrarradicular (CRI); c) suporte ósseo (SO), diâmetro mésio-distal da raiz (DR); d) diâmetro mésio-distal do retentor intrarradicular (DRI). Por meio de parâmetros de referência os retentores foram classificados em aceitáveis, com margem de erro de até 0,2 mm, ou deficientes. Para a análise descritiva os dados foram catalogados utilizando-se o software SPSS 17.0. Resultado Quanto ao comprimento, pela análise da regra dos 2/3 apenas 23,75% dos retentores foram classificados como aceitáveis, enquanto na regra do fulcro dentário essa porcentagem foi de 37,5%. Com relação ao diâmetro mésio-distal 52,5% dos retentores foram aceitáveis. Conclusão Dentro dos limites deste estudo, pode-se concluir que os retentores metálicos fundidos avaliados não estão de acordo com os critérios clínicos ideais.

Introduction Accurate dimensions of cast-metal posts are relevant to the survival of dental prostheses. Objective The aim of this study was to verify if the dimensions of cast-metal posts accord with ideal clinical criteria. Material and method For the evaluation, 285 periapical radiographs, from a total of 80 teeth, were taken from the charts of patients that attended the clinics at the Dental School of the Federal University of Goiás, from March 2008 to October 2012. Only periapical radiographs of single-rooted teeth with post and core were included in the study. The radiographic evaluation was conducted with the assistance of a magnifying glass and a view box, in a room with low luminosity. The dimensions of the post and core were established with the help of a digital caliper, and the following measurements were considered: a) LR (Length Remnant); b) LP (Length Post); c) BS (Bone Support); d) DR (Diameter Root); e) DP (mesiodistal diameter post). The post and core were classified as acceptable or deficient by reference values with a margin of error of 0.2 mm. For descriptive analysis, the data were cataloged using SPSS software (version 17.0). Result With regard to the length of the post and core, only 26.25% and 43.75% of the post and core were classified as acceptable according to the two-thirds rule and fulcrum dental rule, respectively. With regard to the mesiodistal diameter of the post and core, 55% were classified as acceptable. Conclusion Within the limits of this study, it can be concluded that the cast-metal posts evaluated do not accord with the ideal clinical criteria.

Protocolos terapêuticos aceitáveis em odontologia dependem de resultados observados com a proservação. Erros de procedimentos operatórios podem ocorrer e representam fatores de risco capazes de comprometer um dente ou um implante dentário. O objetivo deste artigo é detectar os erros de procedimentos operatórios em dentes tratados endodonticamente e implantes dentários por meio de tomografia computadorizada de feixe cônico. Oitocentos e dezesseis (816) exames tomográficos foram realizados entre Janeiro de 2009 e Outubro de 2010, e apenas aqueles que apresentaram dentes tratados endodonticamente e/ou implantes dentários foram selecionados. A amostra final envolveu 195 exames tomográficos (n=200 dentes e 200 implantes dentários), 72 do gênero masculino, 123 do gênero feminino, com idade média de 51 anos. Em dentes tratados endodonticamente os erros de procedimentos operatórios incluídos foram: subobturação, sobreobturação, e perfuração radicular; enquanto que, para implantes dentários foram incluídos: roscas de implantes expostas, implantes em contato com estruturas anatômicas, e em contato com dentes adjacentes. O nível de significância foi estabelecido em α=5%. Subobturações, sobreobturações e perfurações radiculares foram detectadas em 33,5%, 8% e 4,5%, respectivamente. Implantes dentários com roscas expostas, em contato com estruturas anatômicas, e em contato com dentes adjacentes apresentaram valores de 37,5%, 13% e 6,5%, respectivamente. Erros de procedimentos operatórios foram detectados em dentes tratados endodonticamente e implantes dentários. Os erros mais frequentes foram subobturação em dentes tratados endodonticamente, e roscas expostas em implantes dentários.

Acceptable therapeutic protocol in dentistry depends on the outcomes obtained with follow up. Operative procedural errors (OPE) may occur and they represent risk factors able to compromise a tooth or a dental implant. The aim of this study was to detect the OPE in endodontically treated teeth and dental implants, using cone beam computed tomography (CBCT).Eight hundred and sixteen CBCT exams were performed between January 2009 and October 2010, and only those which presented endodontically treated teeth and/or dental implants were selected. The sample was as follows: 195 CBCT exams (n=200 teeth and 200 dental implants), 72 male, 123 female, with mean age of 51 years.In endodontically treated teeth, OPE included underfilling, overfilling, and root perforation; OPEin dental implants were thread exposures, contact with anatomical structures, and contact with adjacent teeth. Kolmogorov-Smirnov test was used for statistical analysis, with significance level set at α=0.05. Underfilling, overfilling, and root perforations were detected in 33.5%, 8% and 4.5% of the teeth, respectively. Dental implants with thread exposures, contact with important anatomical structures and contact with adjacent teeth were seen in 37.5%, 13% and 6.5% of the cases, respectively. OPE were detected in endodontically treated teeth and dental implants, and underfilling and thread exposures were the most frequent occurrences, respectively.

This study analyzed the reaction layer and measured the marginal crown fit of cast titanium applied to different phosphate-bonded investments, prepared under the following conditions (liquid concentration/casting temperature): Rema Exakt (RE) - 100%/237°C, 75%/287°C, Castorit Super C (CS)-100%/70°C, 75%/141°C and Rematitan Plus (RP)- 100%/430°C (special to titanium cast, as the control group). The reaction layer was studied using the Vickers hardness test, and analyzed by two way ANOVA and Tukey's HSD tests (α = 0.05). Digital photographs were taken of the crowns seated on the die, the misfit was measured using an image analysis system and One-way ANOVA, and Tukey's test was applied (α = 0.05). The hardness decreased from the surface (601.17 VHN) to 150 μm (204.03 VHN). The group CS 75%/141°C presented higher hardness than the other groups, revealing higher surface contamination, but there were no differences among the groups at measurements deeper than 150 μm. The castings made with CS - 100%/70°C presented the lowest levels of marginal misfit, followed by RE -100%/237°C. The conventional investments CS (100%) and RE (100%) showed better marginal fit than RP, but the CS (75%) had higher surface contamination.

This study examined by means of scanning electron microscopy (SEM), the attachment of Streptococcus mutans and the corrosion of cast commercially pure titanium, used in dental dentures. The sample discs were cast in commercially pure titanium using the vacuum-pressure machine (Rematitan System). The surfaces of each metal were ground and polished with sandpaper (#300-4000) and alumina paste (0.3 µm). The roughness of the surface (Ra) was measured using the Surfcorder rugosimeter SE 1700. Four coupons were inserted separately into Falcon tubes contained Mueller Hinton broth inoculated with S. mutans ATCC 25175 (10(9) cuf) and incubated at 37 °C. The culture medium was changed every three days during a 365-day period, after which the falcons were prepared for observations by SEM. The mean Ra value of CP Ti was 0.1527 µm. After S. mutans biofilm removal, pits of corrosion were observed. Despite the low roughness, S. mutans attachment and biofilm formation was observed, which induced a surface corrosion of the cast pure titanium.

As the adaptation of titanium crowns obtained by Rematitan Plus investment, specific for titanium, is not recognized to be suitable, this study evaluated the effect of the concentration of the specific liquid and the temperature of the mold of investments on the internal misfit of crowns cast on commercially pure titanium. Individual dies of epoxy resin were obtained, representing teeth prepared for full-crown restoration with a 6-degree axial surface convergence angle and shoulder (1.0 mm). For the waxing of each crown, a ring-shaped stainless steel matrix (8.0mm internal diameter; 7.5 mm height) was adapted above the individual dies of epoxy resin. The Rematian Plus investment was mixed according to the manufacturer's instructions using two different concentrations of the specific liquid: 100%, 75%. Casting was performed in a Discovery Plasma Ar-arc vacuum-pressure casting machine with molds at temperatures of 430ºC, 515ºC and 600ºC. The crowns were cleaned individually in a solution (1% HF + 13% HNO3) for 10 min using a ultrasonic cleaner, with no internal adaptations, and luted with zinc phosphate cement under a 5 kg static load. The crown and die assemblies were embedded in resin and sectioned longitudinally. The area occupied by cement was observed using stereoscopic lens (10X) and measured by the Leica Qwin image analysis system (mm²). The data for each experimental condition (n=8) were analyzed by Kruskal-Wallis non-parametric test (á=0.05). The results showed that liquid dilution and the increase in mold temperature did not significantly influence the levels of internal fit of the cast titanium crowns. The lowest means (±SD) of internal misfit were obtained for the 430ºC/100%: (7.25 mm² ±1.59) and 600ºC/100% (8.8 mm² ±2.25) groups, which presented statistically similar levels of internal misfit.

The aim of the work was to evaluate the influence of the temperature of investment healting on the tensile strength and Vickers hardness of CP Ti and Ti-6Al-4V alloy casting. Were obtained for the tensile strength test dumbbell rods that were invested in the Rematitan Plus investment and casting in the Discovery machine cast. Thirty specimens were obtained, fiftten to the CP Titanium and fifteen to the Ti-6Al-4V alloy, five samples to each an of the three temperatures of investment: 430ºC (control group), 480ºC and 530ºC. The tensile test was measured by means of a universal testing machine, MTS model 810, at a strain of 1.0 mm/min. After the tensile strenght test the specimens were secctioned, embedded and polished to hardness measurements, using a Vickers tester, Micromet 2100. The means values to tensile tests to the temperatures 430ºC, 480 and 530: CP Ti (486.1 - 501.16 - 498.14 -mean 495.30 MPa) and Ti-6Al-4V alloy (961.33 - 958.26 - 1005.80 - mean 975.13 MPa) while for the Vickers hardness the values were (198.06, 197.85, 202.58 - mean 199.50) and (352.95, 339.36, 344.76 - mean 345.69), respectively. The values were submitted to Analysis of Variance (ANOVA) and Tukey,s Test that indicate differences significant only between the materials, but not between the temperature, for both the materias. It was conclued that increase of the temperature of investment its not chance the tensile strength and the Vickers hardness of the CP Titanium and Ti-6Al-4V alloy.

O objetivo deste estudo foi avaliar o efeito de tratamentos térmicos na dureza Vickers do titânio comercialmente puro e da liga Ti-6Al-4V. Corpos-de-prova cilíndricos com 6 mm de diâmetro foram fundidos no sistema Rematitan. Os corpos-de-prova de titânio comercialmente puro e da liga Ti-6Al-4V foram divididos aleatoriamente em 3 grupos (n=10): controle (sem tratamento térmico); tratamento 1 (T1): aquecido a 750ºC por 2 h; tratamento 2 (T2): aquecido a 955ºC por 1 h e envelhecido a 620ºC por 2 h. Após os tratamentos térmicos, os corpos-de-prova foram incluídos em resina acrílica, a superfície foi regularizada e polida, e a dureza foi mensurada. As médias de dureza Vickers (VHN) e os desvios padrão foram analisados estatisticamente usando o teste de Kruskal-Wallis com nível de significância a 5%. Para o titânio comercialmente puro, a média de dureza do grupo T2 (259,90 VHN) foi significativamente maior que os outros grupos (controle-200,26 VHN e T1-202,23 VHN) (p<0,05), que apresentaram valores médios similares (p>0,05). Para a liga Ti-6Al-4V, diferenças estatisticamente significantes foram observadas entre os três grupos: T2 (369,08 VHN), T1 (351,94 VHN) e controle (340,51 VHN) (p<0,05). Os resultados demonstraram diferente comportamento de dureza do titânio comercialmente puro e da liga Ti-6Al-4V quando diferentes tratamentos foram usados. Para o titânio comercialmente puro, a média de VHN grupo T2 foi consideravelmente maior que as médias dos grupos controle e T1, os quais demonstraram médias similares entre si. Para a liga Ti-6Al-4V, entretanto, a média de VHN registrada para cada grupo pode ser apresentada da seguinte maneira: T2>T1>controle.

The purpose of this study was to evaluate the effect of heat treatments on the Vickers hardness of commercially pure titanium and Ti-6Al-4V castalloys. Six-millimeter-diameter cylindrical specimens were cast in a Rematitan System. Commercially pure titanium and Ti-6Al-4V alloy specimens were randomly assigned to 3 groups (n=10) that received the following heat treatments: control (no heat treatment); treatment 1 (T1): heating at 750ºC for 2 h; and treatment 2 (T2): annealing at 955ºC for 1 h and aging at 620ºC for 2 h. After heat treatments, the specimens were embedded in acrylic resin and their surface was ground and polished and hardness was measured. Vickers hardness means (VHN) and standard deviations were analyzed statistically by Kruskal-Wallis test at 5% significance level. For commercially pure titanium, Vickers hardness means of group T2 (259.90 VHN) was significantly higher than those of the other groups (control - 200.26 VHN and T1 - 202.23 VHN), which presented similar hardness means to each other (p>0.05). For Ti-6Al-4V alloy, statistically significant differences were observed among the three groups: T2 (369.08 VHN), T1 (351.94 VHN) and control (340.51 VHN) (p<0.05). The results demonstrated different hardness of CP Ti and Ti-6Al-4V when different heat treatments were used. For CP Ti, VHN means of T2 group was remarkably higher than those of control and T1 group, which showed similar VHN means to each other. For Ti-6Al-4V alloy, however, VHN means recorded for each group may be presented as follows: T2>T1>control.